Black Box IC109A-R2 Manuel d'installation Page 141
- Page / 164
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
13563230-216-229-B1
3
© 2007 Schneider Electric. All Rights Reserved.
Commissioning
Checking Sepam™ B83
Additional Phase Voltage
Input Connections
Block Diagram with Two Additional VTs
DE51261
* Detection of Plugged Connector (required for proper operation. Installed manually)
Procedure
Use the diagram above to perform the following steps
Checking with a Three-Phase Voltage Generator
1 Turn the generator on.
2 Apply the three generator voltages Van, Vbn, Vcn, balanced and set to the rated
secondary phase-to-neutral voltage of the additional VTs (V’
Ln
s
= V’
LL
s
/ 3)
3 Use the SFT2841 software to check that:
b the values indicated for each of the phase-to-neutral voltages V’an, V’bn,
V’cn, and the positive sequence voltage V’1 are approximately equal to the
VT's rated primary phase-to-neutral voltage (V’
Ln
p = V’
LLp
/ 3)
b the value of each of the phase-to-phase voltages V’ab, V’bc, V’ca is equal to
the VT's rated primary phase-to-phase voltage (V’
Ln
p)
4 Turn the generator off.
Checking with a Single-Phase Voltage Generator
1 Turn the generator on.
2 Apply the generator voltage V
Ln
set to the rated secondary phase-to-neutral
voltage of the additional VTs (V’
Ln
s = V’
LLs
/ 3) across Sepam™ voltage input
terminals 1 and 5 (via the text box).
3 Use the SFT2841 software to check that the value indicated for the phase-to-
neutral voltage V’ab is approximately equal to the VT's rated primary phase-to-
neutral voltage (V’
Ln
p = V’
LLp
/ 3).
4 Apply the generator voltage V-N set to the rated secondary phase-to-neutral
voltage of the additional VTs (V’
Ln
s = V’
LLs
/ 3) across Sepam™ voltage input
terminals 3 and 5 (via the text box).
5 Use the SFT2841 software to check that the value indicated for the phase-to-
neutral voltage V’bc is approximately equal to the VT's rated primary phase-to-
neutral voltage(V’
Ln
p = V’
LLp
/ 3).
6 Turn the generator off when you finish this test.
Van
Vbn
Vcn
Vr
V‘an
V‘bn
V‘cn
V‘r
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.fr. Tous droits réservés | 0.163 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels