Black Box IC109A-R2 Manuel d'installation Page 81
- Page / 164
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
75
1
© 2007 Schneider Electric. All Rights Reserved.
63230-216-229-B1
Installation
Communications Wiring
Cable Pinouts
Cable pinouts for CAB-107 and CAB-108 cables are shown below.
.
Network Daisy Chain Practices (including Shield Grounding)
Sepam
Ser.80
No. 2
Sepam
Ser.80
No. 25
ACE959
RS232/RS485
Converter
& Power Supply
TR
TR BR
ACE959
ACE959
Sepam
Ser.80
No. 1
TR
TR
RS232
CCA612
CCA612
CCA612
RS485
System
PC
RS485
Break in
Shield
110 Vac
Notes:
■ RS485 cable is 4-wire plus shield. 2-wire power (24 Vdc) is also required. Recommended cable:
❏ Belden 9841 (1 pair)
❏ Belden 9842 or 8723 (2 pair)
❏ Fileca F3644-1 (2 pair signal/1 pair power)
■ Shield is broken between two grounded shield termination points (typical). Leave the shield intact from source until just
before next
shield ground.
■ Up to 25 Sepam Series 80 relays (maximum) on daisy chain.
■ TR=Terminating Resistor
■ Two TRs are required at each end of an RS485 4-wire diasy chain (can be accomplished by setting the movable jumpers
on Sepam module ACE959, the switches on Black Box converter IC109A-R2, or, for series 2000 circuit monitors, using a
Multipoint Communications Adapter MCT-485). For series 4000 circuit monitors and series 600 power meters with a screw-type
terminal block, use an MCTAS-485 (or an MCT-485 with a terminal block). Refer to the device instruction bulletin for more details.
■ BR= Biasing Resistor
■ One BR set required per daisy chain (accomplish by setting switch on Black Box converter IC109A-R2; other converters should
be checked for configurable biasing [recommended at or near system master]).
■ One recommended RS232/RS485 Converter is Black Box IC109A-R2 (power supply separate).
■ Shields should be grounded at one end only.
Shield
Shield
Shield
Shield
RS485
RS485
Break in
Shield
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.fr. Tous droits réservés | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels