Black Box IC109A-R2 Manuel d'installation Page 53
- Page / 164
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
47
1
© 2007 Schneider Electric. All Rights Reserved.
63230-216-229-B1
Installation
Remote Modules
Selection Guide
Four remote modules are options to enhance the Sepam™ base unit functions:
b The number and type of remote modules compatible with the base unit depend
on the Sepam™ application
b The DSM303 remote advanced UMI module is only compatible with base units
that do not have integrated advanced UMIs
Sepam™ Series 80
Item Description Comments S8x, B8x T8x, G8x M8x C8x
MET1482 Temperature sensor module See page 48 0 2 2
MSA141 Analog output module See page 50 1 1 1
DSM303 Remote advanced UMI module See page 52 1 1 1
MCS025 Sync-check module See page 54 1 1 0
Number of sets of interlinked modules / maximum
number of remote modules
Five modules split between two sets
of interlinked modules
Connection
Connection Cables
Different combinations of modules can be connected using cables fitted with two
black RJ45 connectors that come in three lengths:
b CCA770: length = 2 ft (0.6 m)
b CCA772: length = 6.6 ft (2 m)
b CCA774: length = 13.1 ft (4 m)
The modules are linked by cables which provide power and act as functional links
with the Sepam™ unit (connector to connector ,
to , …).
CAUTION
HAZARD OF NON-OPERATION
The MCS025 module must ALWAYS use the
special CCA785 cord supplied with the module. It
has an orange RJ45 plug and a black RJ45 plug.
Failure to follow this instruction can cause
equipment damage.
DE51646
Rules on Inter-Module Linking
1 Link no more than three modules
2 Connect DSM303 or MCS025 modules only at the end of the link
Maximum Advisable Configurations
Sepam™ Series 80: Two Sets of Interlinked Modules
Sepam™ Series 80 has two connection ports for remote modules, and .
Modules may be connected to either port.
Base Cord Module 1 Cord Module 2 Cord Module 3
Set 1 CCA772 MET1482 CCA770 MET1482 CCA774 DSM303
Set 2 CCA772 MSA141 CCA785 MCS025 - -
DE51647
D
Da
Dd
Da
D1
D2
D1
D2
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.fr. Tous droits réservés | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels